Plumber's Essentials: Your Key to Installing a Bathtub
Plumber's Essentials: Your Key to Installing a Bathtub
Blog Article
Are you interested in content concerning How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?
Installing a bathtub isn't exactly rocket science, but it does require strong plumbing, woodworking, and also occasionally, tiling abilities. Changing an old tub with a new one is also a reasonably challenging task. If the old tub is readily accessible, the job can move immediately; if you have to open up a wall to remove the old tub as well as position the brand-new bathtub, the task is much harder. In either instance, the project is within a residence handyman's abilities, although you will certainly require an assistant to leave the old bathtub and also embeded in the new one. See to it you have qualified yourself for the task as well as are comfortable trying it. As opposed to working with a service provider to take control of a halfway-completed project, it is much better to think about using one before you start. Chances are you may need a specialist plumber to make tube connections.
This post will certainly aid you install a new tub in your restroom if you have actually currently purchased a brand-new bathtub and also don't need to change the plan of your previous water supply pipes.
Your devices as well as product list ought to make up the following:
Preparing for the Installation
First of all, the sustaining framework provided with the bathroom must be fitted (if called for) according to the manufacturer's directions. Next, fit the taps or mixer to the bathtub. When suitable the tap block, it is essential to ensure that if the tap includes a plastic washer, it is fitted in between the bathroom as well as the taps. On a plastic bath, it is also reasonable to fit a sustaining plate under the taps device to avoid stress on the bathtub.
Fit the adaptable tap adapters to the bottom of both taps using 2 nuts and olives (sometimes provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and after that pass the outlet through the hole in the bath. Make use of the nut provided by the supplier to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the flexible overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bath. See to it you make use of all of the provided washing machines.
Attach the trap to the bottom of the waste outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Link the bottom of the overflow tube in a similar manner.The bath should now prepare to be suited its last position.
Removing Old Touches
If you require to replace old faucets with brand-new ones as a part of your setup, after that the first thing you need to do is disconnect the water. After doing so, turn on the taps to drain any type of water staying in the system. The procedure of getting rid of the existing taps can be rather troublesome because of the limited accessibility that is frequently the case.
Make use of a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipelines to the faucets. Have a towel ready for the remaining water that will certainly originate from the pipes. As soon as the supply pipes have been removed, utilize the very same tool to loosen up the nut that holds the faucets onto the bath/basin. You will need to quit the single taps from turning throughout this procedure. Once the taps have actually been eliminated, the holes in the bath/basin will have to be cleaned of any kind of old sealing compound.
Prior to going on to fit the new faucets, contrast the pipeline links on the old taps to the brand-new taps. If the old taps are longer than the brand-new faucets, then a shank adapter is needed for the new faucets to fit.
Mounting the Tub
Using both wood boards under its feet, position the tub in the called for placement. The wood boards are practical in uniformly spreading the weight of the bath tub over the location of the boards rather than focusing all the weight onto four little points.
The next objective is to make certain that the bathtub is leveled all round. This can be achieved by checking the spirit level and adjusting the feet on the tub until the spirit level reads level.
To set up faucets, fit all-time low of the furthest adaptable faucet port to the proper supply pipe by making a compression join; after that do the very same for the various other faucet.
Switch on the water system as well as inspect all joints as well as brand-new pipework for leaks as well as tighten them if necessary. Load the tub and likewise inspect the overflow outlet and also the regular outlet for leaks.
Lastly, repair the bathroom paneling as described in the manufacturer's instruction manual. Tiling and also securing around the bathtub ought to wait up until the bathtub has actually been utilized at least once as this will settle it into its last placement.
Fitting New Touches
If the tails of the new taps are plastic, then you will certainly need a plastic port to stop damage to the thread. One end of the port fits on the plastic tail of the tap and also the other end provides a link to the current supply pipes.
If you require to fit a monobloc, then you will certainly call for reducing couplers, which links the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
Next, place the faucet in the placing opening in the bath/basin guaranteeing that the washers remain in location between the faucet and also the sink. Safeguard the tap in place with the maker given backnut. As soon as the faucet is firmly in place, the supply pipelines can be connected to the tails of the taps. The faucets can either be attached by utilizing corrugated copper piping or with normal tap connectors. The previous kind ought to be connected to the tap finishes initially, tightening only by hand. The supply pipes can later on be linked to the other end. Tighten both ends with a spanner after both ends have been connected.
Tiling Around the Tub
In the location where the bath meets the tile, it is needed to secure the accompanies a silicone rubber caulking. This is essential as the fitting can relocate sufficient to break a stiff seal, creating the water to permeate the wall in between the bath and also the tiling, bring about issues with wetness and also possible leakages to the ceiling below.
You can select from a range of coloured sealants to blend in your components and also fittings. They are offered in tubes and cartridges, and can sealing voids up to a size of 3mm (1/8 inch). If you have a larger space to load, you can load it with spins of drenched newspaper or soft rope. Remember to constantly fill the bath tub with water prior to securing, to allow for the movement experienced when the tub is in usage. The sealer can break rather early if you do not think about this motion prior to sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are also quickly available on the marketplace. It is a good idea to fit the floor tiles using waterproof or water-proof glue and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I hope you enjoyed our part on A Step-by-Step Guide to Installing a Bathtub. Thanks for spending some time to read through our blog. Are you aware of somebody else who is fascinated by the niche? Why not share it. We truly appreciate reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Call now! Report this page